Belt and Bed - Your treadmill uses a very high-efficient low-friction bed. Performance is maximized when the bed is kept as clean as possible. Use a soft, damp cloth, or paper towel, wipe the edge of the belt and the area between the belt edge and the frame. Also reach as far as practical directly under the belt edge. This should be done once a month to extend belt and bed life. A mild soap and water solution along with a nylon scrub brush will clean the top of the textured belt. Allow to dry before using.
Belt Dust - This occurs during normal break-in or until the belt stabilizes. Sometimes the black dust from the belt will appear on the floor behind the treadmill, this is normal.
General Cleaning - Dirt, dust, and pet hair can block air inlets and accumulate on the running belt. Please vacuum underneath your treadmill on a monthly basis to prevent excess build-up of dirt that can get sucked up and get into the inner workings under the motor cover. Once a year, you should remove the black motor hood and vacuum out dirt that may accumulate. UNPLUG POWER CORD BEFORE THIS TASK.
BELT ADJUSTMENTS:
Tread-belt Tension Adjustment - Belt tension is not critical for most users. It is very important though for joggers and runners in order to provide a smooth, steady running surface. Adjustment must be made from the rear roller with the 6 mm Allen wrench provided in the parts package. The adjustment bolts are located at the end of the step rails as shown in the diagram below.
Tighten the rear roller only enough to prevent slippage at the front roller. Turn the tread-belt tension adjusting bolts 1/4 turn each and inspect for proper tension by walking on the belt and making sure it is not slipping or hesitating with each step. When an adjustment is made to the belt tension, you must be sure to turn the bolts on both sides evenly or the belt could start tracking to one side instead of running in the middle of the deck.
DO NOT OVERTIGHTEN – Over tightening will cause belt damage and premature bearing failure. If you tighten the belt a lot and it still slips, the problem could actually be the drive belt - located under the motor cover - that connects the motor to the front roller. If that belt is loose it feels similar to the walking belt being loose. Tightening the motor belt should be done by a trained service person.
TREADMILL LUBRICATION
Your Fuel/Spirit Treadmill should require little more maintenance than periodically checking belt alignment and deck lubrication. All treadmills from New Level will come complete with a bottle of deck lubricant. Lubricating under the treadmill belt will ensure superior performance and extend the life expectancy of the treadmill.
Belt/deck lubrication procedure:
Do not lubricate with other than Spirit/Fuel approved lubricant. Your treadmill comes with one bottle of lubricant and extra lubricant can be purchased from New Level direct on 01782 645000 or contact info@new-level.co.uk
Keeping the deck lubricated at the recommended intervals ensures the longest life possible for your treadmill. If the lubricant dries out, the friction between the belt and deck rises and places undue stress on the drive motor, drive belt and electronic motor control board, which could result in failure of these expensive components. Failure to lubricate the deck at regular interval’s may void the warranty. The belt & deck come pre-lubricated and subsequent lubrication should be performed every 180 hours of use. Pretty much all Fuel/Spirit consoles have a built in lubrication reminder indicator that lights every 180 hours of use.
How to check the treadmill mat is lubricated:
Lift one side of the treadbelt and feel the top surface of the running deck. If the surface is slick to touch then NO further lubrication is required.
If the deck is dry apply half the bottle of lubricant supplied with your Fuel/Spirit treadmill.
How to apply?
1. Lift one side of the treadmill belt.
2. Pour half the lubricant under the centre of the treadmill belt on the top surface of the deck.
3. Walk on the treadmill at slow sped for 3-5 minutes to evenly distribute the lubricant applied.
4. Do NOT over lubricate and any excess that comes out from the side of the belt wipe clean.
If you have any further questions please don’t hesitate to contact the experts on 01782 645000 or email us info@new-level.co.uk